Er. I.M.KHAN
Amazon.in6 Nov 2018
What I can mention is I got good price.
I think there is no need to mention about CROWN range of products. What I can mention is I got good price. Read more Read less
- Value for money
We may earn a commission when you buy through these links. It never changes the price or the order.
DudScore
Solid choice with a few things to check.
Early score: few reviewsToday's price against the prices it has sold for.
From 363 days of our own price history, across stores.
No close alternatives in this category and price range yet.
₹31,800
Out of stock at our last check
Ratings on stores (310)Reviews on Whydud (9)
No customer photos yet. Add yours with a review
Customer rating
4.5out of 5
310 ratings across stores
| 5★ | 75% | |
|---|---|---|
| 4★ | 13% | |
| 3★ | 5% | |
| 2★ | 3% | |
| 1★ | 4% |
100% verified purchases
Er. I.M.KHAN
Amazon.in6 Nov 2018
I think there is no need to mention about CROWN range of products. What I can mention is I got good price. Read more Read less
Aman
Amazon.in19 Dec 2018
Great product Read more Read less
Doug
Amazon.in19 Aug 2020
I wanted a powerful pre-amp for my two 12 inch woofers and this delivers. My home theater has two woofers in the floor under the seating and this drives them very well and never seems to get hot at all. Great unit. Read more Read less
Deis Shab
Amazon.in5 Sept 2025
Very good product Read more Read less
Tanusri Dey Manna
Amazon.in8 Jul 2021
Very good product. Cristal clear sound. Read more Read less
shaiphali Singh
Amazon.in25 Jul 2021
Nice Read more Read less
UNC MSEE
Amazon.in15 Aug 2017
This amp is a very good deal for the price in my application. I am utilizing this amp as a power amplifier to drive a pair of really current hungry Magnepan 1.4 speakers. I recently purchased a pair of used Magnepan 1.4 speakers for $250. These are rated at 5 ohm impedance, which is getting on the low end for most general purpose home audio equipment. My current system was being driven by a Marantz SR 7007 receiver which can deliver 125 watts into 8 ohms and up to 195 w into 6 ohms. But it is not rated for the 5 ohm load I'm looking at driving. So, it didn't seem the power supply on the built in power amplifier would be sufficient to meet the current demands if I wanted to turn the volume up and really test out these speakers. I.e., the low resistance speakers would pull more current than the power supply in the receiver could reasonably deliver at higher volumes or peaks which could potentially damage the amplifier or cause it to overheat. So, I have been looking around for a good power amplifier which was rated down to 4 ohms or less to ensure I would never have any problems. Unfortunately, when you get into home audio amplifiers with this kind of power supply, you really are going to have to pay quite a premium on the amplifier. While, I think these speakers could have benefited from the current that could come from a high end audiophile amplifier and the more sophisticated amplifier design, I just was not looking to spend $1,000++++ to get that kind of power. Enter the Crown amplifier. I had a friend who does the audiophile hobby on a budget recommend the Crown amps as a good bang for the buck. After spending a week reviewing them and really looking around, I though it was a good investment to at least try this amp out for my needs.... especially using Amazon as I could easily just send it back if I wasn't fully satisfied. So, what could it hurt? I ordered the amplifier Sunday and with free Prime two day shipping, I received it Tuesday. I hooked this right up to the pre-outs on my Marantz receiver and set the gain on the Crown to maximum output after I tested it low outputs on the receiver and power amp to check for any obvious issues (I'll explain why I turned the gain all the way up on the Crown in a second) and then turned the volume up on the Marantz.... it sounded great! Just very clean sound. I then did a few quick tweaks on subwoofer crossovers and got a full range signal going to the Magnepans for the first time. I would wager that the sound and detail on this low budget system would beat out systems costing MANY times what I've invested. Now, I have learned a few lessons through this process that I'll try to summarize so that others can learn quicker than I did. 1. You need to take some time to really check and know what the pre-amp output is coming from the device you will be feeding into the Crown power amplifier. The Crown has a switch to allow its sensitivity to be set to 1.4 v or 0.775 v. 1.4 volts is really mostly a characteristic of pro gear. The 0.775v is more representative of home audio equipment. My Marantz puts out 0.4 v therefore the setting of 0.775 v is great for my application (the difference between 0.4 v and 0.775 isn't too large and can be compensated for by getting a higher wattage rated amplifier). But why is this important? The pre-amp signal is sent as a variable voltage with a maximum voltage that the preamp circuit can reasonably produce without clipping. If you push the volume on your preamp too high and ask it to send a signal in excess of the capabilities of the pre-amp circuit you will get a lot of distortion and clipping of the signal which is a very quick way to kill your equipment. You want to avoid this at all costs. If the pre-amp signal going to the power amplifier is much higher than the power amplifier's sensitivity rating, you can be asking the power amplifier to amplify this signal too much and exceed the power rating of the power amp and get signal clipping if you turn the volume too high. So, you really want to understand this mating and get it reasonably close. If you get it way too low, you will never get the full output that the power amplifier is capable of even when all the gains are set to maximum on the power amp and the pre amp. This would be okay if you select an amplifier that is oversized for what you really need for your speakers. So, my application falls into this category. My receiver only puts out 0.4 v and I have the power amp set to 0.775 v. My speakers are rated up to 200 w RMS I believe. So, I really don't want to be sending around 400w into my speakers anyways, which is probably in the ballpark for what the Crown XLi1500 puts out into a 5 ohm load. Speaking to Crown technical support, I should still reasonably get up close to 300 w into these speakers with my set up.... which is PLENTY of power. In general, you want to consider purchasing an amplifier which is rated a bit higher than your application an
Matteo
Amazon.in30 Nov 2025
Per quello che costa va benissimo,usato anche in hi fi non sfigura affatto,un filo rumorose le ventole ma per il resto niente da dire,rapporto qualita' prezzo elevato Read more Read less
AMADO SANTILLAN MONTIEL
Amazon.in8 Apr 2023
Funciona correctamente a la descripción, sin problema Read more Read less